Used 1978 Datsun 280z - Highly Modified - cars & trucks - by owner -... for sale in Pendleton, OR
$27,500
Vehicle Details
1978 Year | $27,500 Price | grey Exterior Color |
good General Condition | clean Title Status | 8 cylinders Cylinders |
manual Transmission | rwd Drive Train | gas Fuel Type |
Vehicle Description
The time has come for someone else to drive and enjoy this car. I built this car as something I could drive anywhere and be competitive in several arenas. It was designed to turn, but goes pretty good in a straight line also.
This car was originally a California car, and over the years I have removed / repaired all the rust I have found, which wasn't much.
The paint is an older single stage, which looks good overall but is far from perfect. The dash was fixed about 10 years ago, but has since cracked.
The car has made 695 HP / 705 TQ on a mustang dyno. E85 and 20# of boost. At this power level it has been through the quarter at 9.7x at 150mph with a 1.40 60'. Several changes have been made since this, and I believe it would go low 9's with some work. Or, throw a glide in it and go run in the 8's. The Datsun is your oyster.
This car is an absolute gas to drive and turns a lot of heads. For the right price, I will include the pictured Datsun trailer which sits on a custom frame and torsion axle. It is very light, and pulls well behind the car (YES, it has a trailer hitch!)
Engine:
2005 Gen 4 - 5.3L V8
Stock bottom end ( ring gap opened up to .030" )
Head studs
706 heads
LS9 head gaskets
Brian Tooley Racing Dual valve springs
Chromoly pushrods
Tick Performance Turbo Cam - 217/225 .638/.621 114+4
LS2 Timing chain and guide
LS3 Corvette Oil Pan
LS1 Intake - modifed to remove all excess ports
Howe racing double pass aluminum radiator
Taurus e-fan and aluminum shroud
Painless wiring fan controller
Engine Management / Fuel:
Holley HP EFI
Holley Fuel Rails
Holley 120# Injectors
AN10 feed line (alcohol safe)
AN6 Return (PTFE)
Sumped Aluminum cell that uses stock filler
Magnafuel 50 micron pre filter
Walbro 255 external pumps (x3) 1 always runs, 2 kick on when intake manifold pressure reaches 5#
Magnafuel 10 micron post filter
Turbonetics 7875 Ball bearing turbo .96 AR
Precision 46mm wastegate, recirculated
3" intercooler
2.25" hot side merged to 2.5"
3.5" exhaust, split to dual 3" out the rear
Viair 100 Onboard air for boost control
Transmission
New Magnum T56 2.66 Ratio - just swapped in less than 1500 miles ago
Quicktime SFI Steel bellhousing
McCleod RXT Dual disk clutch w/ steel flywheel - also <1500 miles ago
Rear axle
2004 Mustang cobra 8.8 IRS housing
Ford Racing 3.55 gears, trac-loc
Driveshaft shop Custom axles / driveshaft
31 spline Billet chromoly inner stubs with Porsche 930 CV. 300M bars mated to a Z32 N/A outer with chromoly internals.
Driveshaft is 3.5" aluminum. Has a driveshaft loop attached to trans crossmember
Suspension/chassis
T3 Rear uprights - made custom to center the wheel in the well
Fronts are stock tubes that have been shortened with Ground Control coilover kit
T3 TC rods
T3 roll center adjusters
Weld-in Camber plates
Subframe connectors mating front and rear subframes
1.75" DOM 10 Point Cage
Poly suspension bushings throughout
Tokico adjustable inserts
Front brakes are off of a 1982 BMW 733i
Rear brakes are off of a 300ZX
Working E Brake!
Interior
Seats are Corbeau FX1 Pro's
Gauges are Autometer ultralight electronic
Cage is 10 point 1.75" DOM
Momo Leather steering wheel
5 point harnesses
Wheels / Tires
Rota RB-R 17x9.5
275/40 R17 Nitto NT555
Draglites with OLD 28x10.5x15's and front tires.
If the car is still listed, I still have it. I'm not looking for a trade at this time, of anything other than a stack of cash.
This car was originally a California car, and over the years I have removed / repaired all the rust I have found, which wasn't much.
The paint is an older single stage, which looks good overall but is far from perfect. The dash was fixed about 10 years ago, but has since cracked.
The car has made 695 HP / 705 TQ on a mustang dyno. E85 and 20# of boost. At this power level it has been through the quarter at 9.7x at 150mph with a 1.40 60'. Several changes have been made since this, and I believe it would go low 9's with some work. Or, throw a glide in it and go run in the 8's. The Datsun is your oyster.
This car is an absolute gas to drive and turns a lot of heads. For the right price, I will include the pictured Datsun trailer which sits on a custom frame and torsion axle. It is very light, and pulls well behind the car (YES, it has a trailer hitch!)
Engine:
2005 Gen 4 - 5.3L V8
Stock bottom end ( ring gap opened up to .030" )
Head studs
706 heads
LS9 head gaskets
Brian Tooley Racing Dual valve springs
Chromoly pushrods
Tick Performance Turbo Cam - 217/225 .638/.621 114+4
LS2 Timing chain and guide
LS3 Corvette Oil Pan
LS1 Intake - modifed to remove all excess ports
Howe racing double pass aluminum radiator
Taurus e-fan and aluminum shroud
Painless wiring fan controller
Engine Management / Fuel:
Holley HP EFI
Holley Fuel Rails
Holley 120# Injectors
AN10 feed line (alcohol safe)
AN6 Return (PTFE)
Sumped Aluminum cell that uses stock filler
Magnafuel 50 micron pre filter
Walbro 255 external pumps (x3) 1 always runs, 2 kick on when intake manifold pressure reaches 5#
Magnafuel 10 micron post filter
Turbonetics 7875 Ball bearing turbo .96 AR
Precision 46mm wastegate, recirculated
3" intercooler
2.25" hot side merged to 2.5"
3.5" exhaust, split to dual 3" out the rear
Viair 100 Onboard air for boost control
Transmission
New Magnum T56 2.66 Ratio - just swapped in less than 1500 miles ago
Quicktime SFI Steel bellhousing
McCleod RXT Dual disk clutch w/ steel flywheel - also <1500 miles ago
Rear axle
2004 Mustang cobra 8.8 IRS housing
Ford Racing 3.55 gears, trac-loc
Driveshaft shop Custom axles / driveshaft
31 spline Billet chromoly inner stubs with Porsche 930 CV. 300M bars mated to a Z32 N/A outer with chromoly internals.
Driveshaft is 3.5" aluminum. Has a driveshaft loop attached to trans crossmember
Suspension/chassis
T3 Rear uprights - made custom to center the wheel in the well
Fronts are stock tubes that have been shortened with Ground Control coilover kit
T3 TC rods
T3 roll center adjusters
Weld-in Camber plates
Subframe connectors mating front and rear subframes
1.75" DOM 10 Point Cage
Poly suspension bushings throughout
Tokico adjustable inserts
Front brakes are off of a 1982 BMW 733i
Rear brakes are off of a 300ZX
Working E Brake!
Interior
Seats are Corbeau FX1 Pro's
Gauges are Autometer ultralight electronic
Cage is 10 point 1.75" DOM
Momo Leather steering wheel
5 point harnesses
Wheels / Tires
Rota RB-R 17x9.5
275/40 R17 Nitto NT555
Draglites with OLD 28x10.5x15's and front tires.
If the car is still listed, I still have it. I'm not looking for a trade at this time, of anything other than a stack of cash.